Browsing by Author "Aksoy, Muhammed Osman"
Now showing 1 - 3 of 3
- Results Per Page
- Sort Options
Item An experimental and numerical study of wind effects on a ground-mounted solar panel at different panel tilt angles and wind directions(Elsevier, 2021-06) Aksoy, Muhammed Osman; Yemenici, Onur; Uludağ Üniversitesi/Mühendislik Fakültesi/Makine Mühendisliği Bölümü; GKS-5251-2022; 36676656200The wind effects on a ground-mounted solar panel under the influence of the panel tilt angles and wind directions were investigated; both experimentally and numerically. The ground-mounted solar panel was used with tilt angles of 25° and 45° for a Reynolds number of 6.4 × 104. Wind directions were varied from 0° to 180° at 30° intervals. A constant-temperature hot wire anemometer and a pressure scanner system were used to measure velocity and turbulence intensities and static pressure, respectively, in the wind tunnel. Numerical analyses were carried out via computational fluid dynamics methodology using the realizable k-ε turbulence model. The results showed that the flow structure had been significantly affected by the wind directions and panel tilt angles. The higher panel tilt angle caused stronger vortex shedding fluctuations, and higher velocity zones shedding frequencies. As with the flow structure, the design-relevant wind loads on the solar panel were also shown to be dependent on the wind direction and panel angle. The net pressure coefficients of the solar panel increased with the higher panel tilt angle. The critical wind directions were obtained as 300 and 1500 in terms of overturning moments, while 1800 and 00 wind directions were critical in terms of uplift and drag, respectively. The numerical results of the wind loads showed a good agreement with the experimental results.Item Güneş panellerine etkiyen rüzgar yüklerinin nümerik analizi(Bursa Uludağ Üniversitesi, 2019-09-17) Aksoy, Muhammed Osman; Yemenici, Onur; Bursa Uludağ Üniversitesi/Fen Bilimleri Enstitüsü/Makine Mühendisliği Anabilim Dalı.; 0000-0001-5490-0950; 0000-0003-0011-8343Fosil yakıtların gün geçtikçe azalması nedeniyle dünyanın enerji ihtiyacının karşılanması için yapılan alternatif enerji çalışmaları her geçen gün artmaktadır. Güneş enerjisi enerji ihtiyacını karşılamak için kullanılabilecek en önemli kaynaklar arasında olduğundan güneş panelleri enerji üretiminde büyük bir rol oynamaktadır. Bu çalışmada güneş panelleri üzerine etki eden rüzgar yükleri Hesaplamalı Akışkanlar Dinamiği yöntemlerinden yararlanılarak incelenmiştir. Analizler 3 boyutlu bir akış alanı içerisinde sürekli durumlu ve standart k-ε türbülans modeli kullanılarak yürütülmüştür. Yapılan çalışmalarda 10 m/s ve 20 m/s olmak üzere iki farklı rüzgar hızı, 25°, 35° ve 45° olmak üzere üç farklı panel eğim açısı ve 0°, 30°, 60°, 90°, 120°, 150° ve 180° olmak üzere yedi farklı rüzgar yönü kullanılmıştır. Her iki rüzgar hızında da benzer hız ve basınç dağılımları elde edilmiştir. En yüksek net basınç katsayısı değeri 45° eğimli panelde 180° rüzgar yönünde 1,21 olarak tespit edilmiştir. En düşük net basınç katsayısı ise 45° panel eğim açısı ve 60° rüzgar yönünde oluşup -0,81 değerine sahiptir. En yüksek sürüklenme katsayısı olan 1,12 değeri 45° eğimli panelde 180° rüzgar yönünde elde edilmiştir. Maksimum kaldırma katsayısının değeri 1.51 olup 25° eğim açılı panelde 120° rüzgar yönünde tespit edilmiştir.Item Numerical study of wind loads on A solar panel at different inclination angles(IEEE, 2018) Yemenici, Onur; Aksoy, Muhammed Osman; Uludağ Üniversitesi/Mühendislik Fakültesi/Makine Mühendisliği Bölümü.; 36676656200; 57204437067A numerical analysis using Computational Fluid Dynamics methodology was carried out to study the effect of the different inclination angles on wind loads of solar panel. The wind flow is simulated as turbulent, incompressible flow with a free stream velocity of 10 m/s and a wind direction of 180(0) and the inclination angles is chosen as 25(0) , 30(0) and 35(0) . The finite-volume-method is employed to solve the governing equations, coupled with the k-epsilon turbulence model with standard-wall treatment. The results indicate that pressure magnitudes on the panel were increased with the inclination angle. The maximum lift and drag force is appeared for the 35(0 )inclination.